New Guard Coatings

Sherwin Williams Resuflor Screed

Sherwin Williams Resuflor Screed

A heavy duty, epoxy resin floor screed, with high chemical resistance and strong colour definition.

  • Pack Size: 22.5 and 45kg

Sherwin Williams Resuflor Screed

Sherwin Williams Resuflor Screed is a heavy duty epoxy resin floor screed.

Pack Size: 22.5kg and 45kg

 

Product Description

Sherwin Williams Resuflor Screed is a heavy duty, epoxy resin floor screed, with high chemical resistance and strong colour definition. Sealing is necessary where impervious finishes are required. The RSL Resuflor Screed formulation uses an aggregate component free of crystalline silica promoting a more environmentally friendly product with less dust compared to traditional epoxy resin screeds.

 

Product Benefits

  • Hard wearing durable repairs for industrial use
  • Ease of application
  • Can be used as a repair system
  • Can be feather edged
  • Excellent abrasion and impact resistance
  • Low odour
  • Can be used to form coving and falls

 

Recommended Uses

  • Chemical production and storage
  • Printing and packaging areas
  • Engineering facilities
  • Automotive industry
  • Aerospace production areas
  • Industrial workshops

 

Colours

White RAL9003, Black RAL9017, Red RAL3011, Light Grey RAL7004, Dark Grey RAL7005

Yield

22.5Kg will cover 2.81 m2 @ 4mm or 1.87 m2 @ 6mm
* Coverage rate is calculated based on a sealed and smooth surface and may vary based on the substrate roughness and other conditions.

Finish

Smooth screed.

 

Preparation

New concrete Floors: Must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue detergent is washed and removed by rinsing with clean water.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on inter-coat adhesion and suitability as it may not be compatible with existing floor coating. Where over-coating other systems such as epoxy coatings or screeds, as part of a specified composite system in the data sheets, please follow the recoat time as stated in the individual data sheets, the coating in each stage should be tack free, but not fully cured. If fully cured then mechanical preparation is required to ensure inter-coat adhesion.

 

Priming

Open and porous substrates may require priming with Resuprime ST on dry substrates only with less than 75% ERH reading. Where the Relative Humidity of a substrate exceeds 75% ERH Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203. The number of coats to be applied is chosen in accordance with the following table. ERH % Required Coating Thickness 75-85 1 coat of Resuprime MVT at 200 microns per coat 85-92 2 coats of Resuprime MVT at 200 microns per coat 92-97 3 coats of Resuprime MVT at 200 microns per coat For further information please refer to recommended individual product data sheets.

 

Product Application

The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation. Mixing: Pre-mix the coloured base component to a uniform consistency (N.B. base will appear gelled in the tin but will become fluid with mixing) then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Add the aggregate component slowly whilst mixing. Mix using an electric mixer for approximately two to three minutes until the three components have fully combined. For larger units a forced action mixer may be required to fully combine the aggregate into the resins. Resuscreed 45 should be worked with a trowel or float to achieve a dense, compacted finish. This is best achieved by the application of smooth even pressure in one direction, gradually increasing the pressure as the material compacts and beds down. Over-working the material will draw fines to the surface which may result in resin-rich spots and finish variations.

 

Contact Us

For further advice regarding the use of this product, technical support or a quotation please contact us.

Download Datasheet

Reviews

There are no reviews yet.

Be the first to review “Sherwin Williams Resuflor Screed”

Your email address will not be published. Required fields are marked *